Siemens SIMOTION P320-3 Manual Download

Page: 37 / 150

Hardware description

3.2 SIMOTION P320-3 PC unit

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

3.2.2

Connection components

Interfaces and power supply

Position of the connection elements

Pos Designation

Description

①

24 VDC

Connection for a 24 VDC power supply

②

DVI/VGA

DVI/VGA connection for CRT or LCD monitor with DVI interface

③

USB

4 USB 2.0 connections, high-speed / low current

④

PN/IND. ETHERNET

RJ45 Ethernet connection 1 (exclusive PCI interrupt) for 10/100/1000 Mbps

⑤

PROFINET

PROFINET onboard interface with three ports (RJ45 connections)

⑥

COM

Serial interface (RS232) 9-pin D-Sub connector

⑦

USB strain-relief

fastener

The USB strain relief must be fastened to the device enclosure with an oval-head screw

(M4 thread). The USB cables can be fastened to the strain-relief assembly with a cable

tie.

⑧

PE terminal

The PE terminal (M4 thread) must be connected to the protective ground conductor of the

plant, in which the device is to be installed. The minimum conductor cross-section may not

be less than 5 mm

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands