Siemens SIMOTION P320-3 Manual Download

Page: 135 / 150

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

135

Standards and approvals

A.1

General rules

CE marking

Our products satisfy the requirements and protection objectives of the EC

Directives and comply with the harmonized European standards (EN).

Electromagnetic compatibility

Standards for EMC are satisfied, if the EMC Installation Guideline is observed.
SIMOTION products are designed for industrial use in accordance with product standard DIN

EN 61800-3, Category C2.

cULus Approval

Listed component mark for United States and the Canada Underwriters

Laboratories (UL) according to Standard UL 508, File E164110, File E115352,

File E85972.

EMC

USA
Federal

Communications

Commission
Radio Frequency

Interference

Statement

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference in which case the user

will be required to correct the interference at his own expense.

Shielded Cables

Shielded cables must be used with this equipment to maintain compliance with

FCC regulations.

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands