Siemens SIMOTION P320-3 Manual Download

Page: 127 / 150

SIMOTION P320-3 and Panel Fronts
Manual, 02/2012

127

Spare parts/Accessories

11.1

Power supply

11.1.1

Over of power supply

An external power supply is needed to connect the SIMOTION P320-3 to the network.
The power supply must provide the following values for the SIMOTION P320-3:

Output voltage:

20.4 ... 28.8 VDC, typically 24 V

Output power:

Typically 40 W (SIMOTION P320-3 alone), max.

130 W

Max. start-up current (for 30 ms):

4.5 A

Power failure buffering:

At least 3 ms with 10 s recovery time

Dynamic upper voltage limit:

30.2 V

Dynamic lower voltage limit:

18.5 V

Voltage ripple:

Note
The relevant order numbers and more detailed information about the listed accessories can

be obtained from the online catalog in the Siemens A&D Mall

(

Summary of Contents for SIMOTION P320-3























































































































































Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands

Siemens SIMOTION P320-3, Manual

Search results

Summary of Contents for SIMOTION P320-3

Reviews:

Related manuals for SIMOTION P320-3

Brands by name

Popular brands