Siemens SIMOTICS SD SH 71 315 Series Operating Instructions Manual Download Page 121

Page: 121 / 132

1LE7 shaft heights 71 ... 315
Operating Instructions, 04/2022, A5E51689275A-AA

119

Technical data

B.1

Configurator for drive technology

You can find product information on your motor according to ErP Directive 2019/1781 in the

configurator for drive technology. If you enter the motor order number (MLFB), you will find

technical documentation such as data sheets, characteristic curves and CAD drawings for

your motor: https://siemens.co.in/dtk (

https://siemens.co.in/dtk

)

B.2

Tightening torques

B.2.1

Tightening torques for screw and bolt connections

Bolt locking devices

•

Refit nuts or bolts that are mounted together with locking, resilient, and/or force-

distributing elements with identical, fully-functional elements when re-assembling.

Always renew keyed elements.

•

When screwing together threads secured with a liquid adhesive, use a suitable medium

such as Loctite 243.

•

Always use suitable securing devices or removable adhesives (e.g., Loctite 243) when

installing fixing bolts with a clamping length of less than 25 mm. The clamping length is

taken as the distance between the head of the bolt and the point at which the bolt is

screwed in.

Summary of Contents for SIMOTICS SD SH 71 315 Series





































































































































Search results

Summary of Contents for SIMOTICS SD SH 71 315 Series

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS SD SH 71 315 Series, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS SD SH 71 315 Series

Reviews:

Brands by name

Popular brands