Home
/
Siemens
/
SIMOTICS S-1FK2
/
Operating Instructions Manual

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Share

Page: 215 / 768

Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 215

Decommissioning and disposal

10

10.1

Removing and disposing of the motor

WARNING

Risk of injury through falling motors or machine components
Motors and machine components can fall when being dismantled from the machine. They

can cause serious injury or property damage.
● Secure the machine components being dismantled to prevent them falling.

The removal of the motor must be performed and/or supervised by qualified personnel with

appropriate expert knowledge.

Removing the motor from the machine
1. Check that all parts of the motor are in a no voltage condition.
2. Let the motor cool down enough so that you are not burnt.
3. Disconnect all electrical connections.
4. Remove the fixing elements from the motor.
5. Transport the motor to a suitable location for disposal.
You have removed the motor.
Dispose of the motor in accordance with the local legal requirements.

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

213

«
...
213
214
215
216
217
...
»

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands