Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 212

Page: 212 / 768

9.2

Dimension drawings of converter

SINAMICS S210 FSA

6SL3210-5HB10-1UF0 (100 W)
6SL3210-5HB10-2UF0 (200 W)

ෘ[

[

Figure 9-4

Dimension drawing SINAMICS S210 FSA, dimensions in mm (Inch)

SINAMICS S210 FSB

6SL3210-5HB10-4UF0 (400 W)

ෘ[

[

Figure 9-5

Dimension drawing SINAMICS S210 FSB, dimensions in mm (inches)

Dimension drawings
9.2 Dimension drawings of converter

SINAMICS S210 servo drive system

210

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands