Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 186

Page: 186 / 768

8.1.9

Radial eccentricity, concentricity and axial eccentricity

The shaft and flange accuracies for the 1FK2 motors are implemented to DIN 42955 (IEC

60072-1) as standard (Normal class).

Table 8-3

Radial eccentricity tolerance of the shaft to the frame axis (referred to cylindrical shaft ends)

Motor

Standard (Normal class)

1FK2☐02

0.03 mm

1FK2☐03

0.035 mm

1FK2☐04

0.04 mm

①

Motor

②

Motor shaft

③

Dial gauge

Figure 8-2

Checking the radial eccentricity

Table 8-4

Concentricity and axial eccentricity tolerance of the flange surface to the shaft axis (referred

to the centering diameter of the mounting flange)

Motor

Standard (Normal class)

1FK2☐02

0.08 mm

1FK2☐03
1FK2☐04

Check for concentricity

①

Motor

Check for axial eccentricity

②

Motor shaft

③

Dial gauge

Figure 8-3

Checking the concentricity and axial eccentricity

Technical specifications
8.1 Technical data and properties of the motor

SINAMICS S210 servo drive system

184

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands