Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 177

Page: 177 / 768

Technical specifications

8.1

Technical data and properties of the motor

8.1.1

Technical features

Table 8-1

Technical features

Type of motor

Permanent-magnet synchronous motor

Rotor inertia

1FK21 - High Dynamic - motor with low rotor inertia
1FK22 - Compact - motor with average rotor inertia

Power range

0.05 kW ... 0.75 kW for a line supply voltage of

1 AC 230 V

Cooling

Natural cooling

Insulation of the stator winding according to

EN 60034-1

(IEC 60034-1)

1FK2☐02, 1FK2☐03:
Temperature class 130 (B) for a winding temperature of

ΔT = 80 K at an ambient temperature of +40 °C
1FK2☐04:
Temperature class 155 (F) for a winding temperature of

ΔT = 100 K at an ambient temperature of +40 °C

Pulse voltage insulation class according to

EN 60034-18-41 (IEC 60034-18-41)

IVIC: C

Operating range

-15° to +40° C, derating at higher temperatures

Installation altitude (according to EN 60034–

1 and IEC 60034–1)

≤ 1000 m above sea level, otherwise power derating

Type of construction according to

EN 60034-7 (IEC 60034-7)

IM B5 (IM V1, IM V3)

Degree of protection according to

EN 60034-5 (IEC 60034-5)

IP64, optional IP65

Temperature monitoring

Thermal motor model

Paint finish

Anthracite (RAL 7016)

Shaft extension according to DIN 748-3

(IEC 60072-1)

Plain shaft, optionally with feather key and half-key bal‐

ancing

Radial eccentricity, concentricity, and axial

eccentricity according to DIN 42955

(IEC 60072–1)

Tolerance N (normal)

Vibration severity grade according to EN

60034-14

(IEC 60034-14)

Grade A is maintained up to rated speed

Sound pressure level L

(1 m) according to

DIN EN ISO 1680, max. tol 3 dB(A)

Natural cooling: 55 dB(A)

Encoder systems, built-in with DRIVE-CLiQ

interface

● AS20DQC, absolute encoder singleturn 20-bit
● AM20DQC absolute encoder 20-bit + 12-bit multiturn

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

175

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands