Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 137

Page: 137 / 768

6.8

Safety settings

6.8.1

Safety commissioning

6.8.1.1

Overview

The web server provides you with a commissioning Wizard that navigates you through all of

the steps required when commissioning safety. The basic handling is shown in the following

diagram:

①

Wizard with commissioning steps

②

Access to fault and alarm messages

③

Safety password

④

Start and carry out Safety commissioning

⑤

Selection for controlling the safety functions

⑥

Selects the safety functions

⑦

Activation of the read-only mode (prevents inadvertent changes)

Figure 6-19

Overview: Safety commissioning Wizard

Basic information on commissioning Safety in the web server
● Safety settings can only be made in the "Safety Integrated commissioning" mode. The

converter is in a safe state (STO active) as long as the commissioning mode is active.

The commissioning mode is activated in step "Function selection" using the "Start" button.

● Safety settings are carried out step-by-step in the individual screen forms. A green

checkmark indicates that a commissioning step has been completed.

Commissioning and diagnostics in the Web server

6.8 Safety settings

SINAMICS S210 servo drive system

Operating Instructions, 12/2017, A5E41702836B AA

135

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands