Siemens SIMOTICS S-1FK2 Operating Instructions Manual Download Page 116

Page: 116 / 768

6.4

6.4.1

Users and access rights

There are two or permanent defined users for access to the converter via the web server:
● Administrator

The administrator has full access to the converter data displayed in the web server. A

password is always required for access as administrator.

● SINAMICS

The SINAMICS user has restricted access rights, see the following table. Per default, a

password is not assigned for the SINAMICS user.

Note
Configuring passwords for the users
You can configure the passwords of the two users in the system settings with administrator

rights (see Chapter "Setting or changing user accounts (Page 156)").

The following access rights apply for the users of the web server:

Functions of the web server

Access rights

SINAMICS

Administrator

Start page
Password input

Write

Perform commissioning
● Change drive name
● Perform One Button Tuning
● Use control panel

None

Write

Safety settings
● Make commissioning settings
● Check commissioning in read mode
● Diagnostics

None

Read

Write
Read
Read

Diagnostics
● Display communication settings
● Adapt message list
● Acknowledge alarms

Write
Write
Write

Settings
● Set limits
● Adapt brake control
● Adapt digital inputs
● Adapt parameter list
● Change parameterization

Read
Read
Read
Write
Read

Write
Write
Write
Write
Write

Commissioning and diagnostics in the Web server
6.4 Login/logout

SINAMICS S210 servo drive system

114

Operating Instructions, 12/2017, A5E41702836B AA

Summary of Contents for SIMOTICS S-1FK2

































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands

Siemens SIMOTICS S-1FK2, Operating Instructions Manual

Search results

Summary of Contents for SIMOTICS S-1FK2

Reviews:

Brands by name

Popular brands