Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 50 | Manualshive

Page: 50 / 188

background image

NOTICE
Improper storage or transport
Damage to bearings can result from improper storage or transport.
● On machines that have been supplied with a rotor shipping brace, secure the rotor as per

the notes on transportation (Page 46).

● Protect the motor against strong radial shocks and vibration when storing, as the rotor

shipping brace cannot completely absorb these forces.

● If the customer has already mounted parts, such as a coupling or belt pulley, the bearings

can be damaged during transport. In this case, make sure that the customer uses a rotor

locking device.

WARNING

Risk of explosion due to damaged sealing materials
Storing the machine at temperatures that do not fall within the specified limits can damage

the material of the seals and cause them to fail. As a result, a potentially explosive gaseous

atmosphere can enter the machine and be ignited during commissioning. Explosions can

occur. This can result in death, serious injury or material damage.
The materials used are specially designed for the temperature range required by the

customer. Do not store the machine in conditions that lie outside the specified temperature

limits. The relevant temperature limits are specified on the rating plate.

Long-term storage

If you are storing a machine for more than six months, you must check its condition every six

months. Store the machine in accordance with the specifications in Section "Storage

(Page 48)", and if possible, packed.
● Check the motor for damage.
● Carry out any necessary maintenance work.
● Make sure that the storage conditions are such that condensation cannot form in the motor.
● If the machine is not sealed in plastic film, continually and slightly heat the machine, e.g.

with anti-condensation heating (if available), and ensure that the air circulates in the storage

room.

Storage for longer than three months

Lubricate the machine after every two years of storage.
1. Unpack the machine.
2. Remove the rotor shipping brace, if one is being used.

Preparations for use
4.18 Transport and storage

SIMOTICS FD 1MH1

50

Operating Instructions 08/2017

«
...
48
49
50
51
52
...
»

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Reviews:

No comments

Related manuals for SIMOTICS FD 1LL1

Brand: Kubota Pages: 138

Brand: dunkermotoren Pages: 32

Brand: Onan Pages: 341

COMBIFLUX FP 314 PVDF

Brand: Flux Pages: 28

3564K024BC series

Brand: Faulhaber Pages: 60

Brand: NetGain Motors Pages: 34

Brand: Volvo Penta Pages: 44

Brand: Volvo Penta Pages: 52

Brand: Volvo Penta Pages: 74

Brand: Volvo Penta Pages: 88

Brand: VM Pages: 108

Brand: Jabiru Pages: 56

Featherweight 45

Brand: Seagull Pages: 25

Brand: Honda Pages: 8

Brand: Honda Pages: 2

Brand: Honda Pages: 149

Brand: DANA Pages: 3

Brand: DANA Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands