Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 36

Page: 36 / 188

4.4.5

Power loss

When dimensioning the cooling system, take into account the power losses as a function of

the flow rate for the rated data.

Machine type

Flow rate ± 10 %

[l/min]

Power loss

[kW]

1LH….-3A…-….
1MH….-3A…-….

1LH….-3B…-….
1MH….-3B…-….
1LH….-4A…-….
1MH….-4A…-….

1LH….-4B.1.-….
1MH….-4B.1.-….
1LH….-4B.3.-….
1MH….-4B.3.-….
1LH….-4B.5.-….
1MH….-4B.5.-….

1LH….-4B.7.-….
1MH….-4B.7.-….

Power losses as a function of the flow rate for the rated data.

4.5

Coolant specification

4.5.1

General coolant requirements

The coolant must fulfill the following requirements over the long term. The coolant is based on

filtered drinking/municipal water of the quality specified below.

De-ionized water
Specific conductivity

< 30 μS/cm

Evaporation residue

< 20 mg/l

NOTICE
High percentage of chloride in drinking water
According to Directive 98/83/EC, drinking water may contain up to 250 mg/l of chloride. This

value is too high for the heat sinks, which may be destroyed if inhibitors are not added.
Use inhibitors if the drinking water has an excessively high chloride percentage.

To better explain the coolant recommendations in this document, some of the problems that

can be encountered if the recommendations are ignored are listed in the table below.

Preparations for use
4.5 Coolant specification

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands