Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 28

Page: 28 / 188

Item Description

(13)

Rated voltage [V] and connections

(27)

Direction of rotation

(14)

Rated current [A]

(28)

Data matrix code (order number and serial

number)

Relevant directives

The following directives are relevant for the SIMOTICS motor series.

European low-voltage directive
The SIMOTICS motor series complies with the requirements of the low-voltage directive

2014/35/EU.

European machinery directive
The SIMOTICS motor series does not fall within the area of validity of the machinery directive.

However, the use of the products in a typical machine application has been fully assessed for

compliance with the main regulations in this directive concerning health and safety.

European EMC Directive
The SIMOTICS motor series does not fall within the area of validity of the EMC directive. The

products are not considered as devices in the sense of the directive.

Eurasian conformity
The SIMOTICS motor series complies with the requirements of the Russia/Belarus/

Kazakhstan customs union (EAC).

China Compulsory Certification
The SIMOTICS motor series does not fall in the area of validity of the China Compulsory

Certification (CCC).

Underwriters Laboratories
The SIMOTICS motor series generally complies with UL and cUL requirements as component

of motor applications - and is correspondingly listed. Specifically developed motors and

functions are the exceptions in this case. Here, it is important that you carefully observe the

contents of the quotation and that there is a cUL mark on the rating plate (nameplate)!

Quality management system
Siemens AG employs a quality management system that meets the requirements of ISO 9001

and ISO 14001.

Certificates that can be downloaded
You can download certificates for the SIMOTICS motor series at the following link:
Certificates (

https://support.industry.siemens.com/cs/ww/en/ps/13358/cert

)

Description
3.1 Comparison of IEC and GOST standards

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands