Siemens SIMOTICS FD 1LL1 Operating Instructions & Installation Instructions Download Page 26

Page: 26 / 188

AA87

IIB

①

⑪

②

⑫

⑥

⑦

⑧

⑨

⑩

⑬

①

CE- or EAC marking

②

Code for prevention of explosions

③

Equipment group: II not for mining, but other hazardous zones

④

Device category: 3 for infrequent, short-term danger

⑤

Atmosphere: G for gas

⑥

Explosion protection: International

⑦

"nA" or "ec" type of protection

⑧

Explosion group: IIB for ethylene

⑨

Temperature Class: T3 for maximum surface temperature 200 °C

⑩

Device protection level: Gc for an extended level of protection in hazardous zones with

explosive gas mixtures

⑪

Identification number or name of nominated testing agency

⑫

Zone 2

⑬

"X" special conditions

Rating plate

The rating plate shows the identification data and the most important technical data. The data

on the rating plate and the contractual agreements define the limits of proper usage.

Description
3.1 Comparison of IEC and GOST standards

SIMOTICS FD 1MH1

Operating Instructions 08/2017

Summary of Contents for SIMOTICS FD 1LL1





























































































































































































Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands

Siemens SIMOTICS FD 1LL1, Operating Instructions & Installation Instructions

Search results

Summary of Contents for SIMOTICS FD 1LL1

Reviews:

Related manuals for SIMOTICS FD 1LL1

Brands by name

Popular brands