manualshive.com logo in svg

Siemens SIMOTICS CONNECT 400, Operating Instructions Manual, Page: 93 / 120

Share
Download
Siemens SIMOTICS CONNECT 400 Operating Instructions Manual Download Page 93

Procedure

1. Open the "SIDRIVE IQ Config" application.

2. Select the required asset in the device overview. 

3. Tap on the motor symbol 

.

The connectivity module LED flashes. 

7.2.3

Changing measurement and synchronization intervals

The following intervals are preset in the factory: 

• 5 minutes - interval for measuring temperature, vibrations, rotational frequency, operating 

status
You can change these settings within a specified range.

• 15 minutes - interval for calculation of speed, torque and energy consumption

This setting is always three times the short measurement interval that has been set.

• 24 hours - interval for transmission of the stored data to SIDRIVE IQ Fleet

You can change these settings within a specified range of between 1 and 48 hours. 

Note
Effects that influence the battery life

Shorter intervals result in a shorter battery life.

Operation

7.2 Operation with iOS

SIMOTICS CONNECT 400
Operating Instructions, 08/2021, A5E50161952B AE

91

Summary of Contents for SIMOTICS CONNECT 400

























































































































Reviews:

No comments