manualshive.com logo in svg

Siemens SIMOCODE 3UF, Programming And Operating Manual

Share
Download
Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 43

 

SIMOCODE PRO V PN FDI  
Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001 

43

 

  Monitoring Functions

 

9 

9.1

 

Earth Fault 

9.1.1

 

Internal earth-fault monitoring when using a current measuring module or a 1st 

generation current / voltage measuring module 

Internal earth-fault monitoring via current measuring modules or current / voltage measuring 

modules is only possible for motors with a 3-phase connection in networks that are either 

grounded directly or with low impedance. You can activate internal ground-fault monitoring 

by parameterization. 
It covers two different operating conditions: 

●

 

Normal operation to 2x I

s

. The actual operating current must be less than twice the set 

current I

s

. Fault currents of > 30 % of the set current l

s

 will be detected. 

●

 

Start-up or overload operation to 2x I

s

. The actual operating current is greater than twice 

the set current I

s

. Residual currents of >15 % of the effective motor current will be 

detected. 

 

 

NOTICE 
False tripping in the case of internal ground-fault monitoring 
False tripping can occur if you use internal earth-fault monitoring for star-delta circuits. 

During delta operation, the residual current is non-zero due to harmonics. 

 

Response to internal earth-fault monitoring 

Deactivated, signaling, warning, tripping 

Delay  

Setting range: 0 - 25.5 s (0.5 s) 

Activity 

Unless deactivated, this function is always active, regardless of whether the motor is running 

or not (operating state "ON"). 

Summary of Contents for SIMOCODE 3UF













































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands