Siemens SIMOCODE 3UF Programming And Operating Manual Download Page 30

Page: 30 / 172

Motor Protection

7.4 Thermistor

SIMOCODE PRO V PN FDI

Programming and Operating Manual, 05/2020, A5E44499659002A/RS-AA/001

7.4

Thermistor

Thermistor protection is based on a direct temperature measurement in the motor via binary

PTC thermistors which can be connected to either Basic Unit 1 (BU1) or Basic Unit 2 (BU2).

Thermistor protection is used for:

●

motors with high switching frequencies

●

converter operation

●

Motors with heavy starting

●

intermittent operation and/or during braking

●

a restricted air supply

●

speeds that are lower than the rated speed.

In this case, the sensors are mounted in the winding slot or in the bearings of the motor.

Response at tripping level

Here you can choose the SIMOCODE pro response to be executed if the temperature

exceeds the trip level.

Response

Tripping threshold

Disabled

–

Signaling

Warning

Tripping

Note
With motors for EEx e applications, the response must remain set to "tripping".

Sensor fault sensor circuit error

Here you can choose the SIMOCODE pro response to be executed if there is a short circuit

or a wire break in the thermistor sensor cable.

Response

Sensor fault

Disabled

Signaling

Warning

Tripping

Summary of Contents for SIMOCODE 3UF













































































































































































Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands

Siemens SIMOCODE 3UF, Programming And Operating Manual

Search results

Summary of Contents for SIMOCODE 3UF

Reviews:

Related manuals for SIMOCODE 3UF

Brands by name

Popular brands