manualshive.com logo in svg

Siemens SIMATIC TDC, System Manual

The Siemens SIMATIC TDC is a powerful automation system designed for industrial applications. With its comprehensive "System Manual," users can easily understand and configure the device for optimal performance. To access the manual, simply visit our website and download it for free, ensuring a seamless user experience.

Share
Download
background image

 

CPU modules 

 

4.2 CPU module CPU550/CPU551 

SIMATIC TDC hardware 
System Manual, 08/2017, A5E01114865-AL 

97

 

4.2.9

 

Technical specifications/performance features 

Article number  

 

CPU module CPU550 

6DD1600-0BA0 

CPU module CPU551 

6DD1600-0BA1 /  

6DD1600-0BA2 /  

6DD1600-0BA3 

The CPU modules CPU551 with the article numbers 6DD1600-0BA1 and 6DD1600-0BA2 

have been replaced by the modules with the article number 6DD1600-0BA3. 

 

 

Note 
Where two different values are specified for a feature (separated by "/") in the manual, the 

first is valid for the module with article number 6DD1600-0BA1 and the second for the 

module with article number 6DD1600-0BA2 and the third for modules with the article number 

6DD1600-0BA3. 

 

CPU 

 

CPU 

6DD1600-0BA1 
 
 

6DD1600-0BA2 
 

6DD1600-0BA3 

Processor 

64 bit RISC processor 

Clock frequency 

266 MHz   500 MHz 

800 MHz 

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Reviews:

No comments

Related manuals for SIMATIC TDC

CAME Z Series Instruction Manual preview
Z Series
Brand: CAME Pages: 12
CAME Z Series Technical Documentation Manual preview
Z Series
Brand: CAME Pages: 16
Ultrak KEGS5000 User Manual preview
KEGS5000
Brand: Ultrak Pages: 41
Zander Aachen ZX Series Quick Start Manual preview
ZX Series
Brand: Zander Aachen Pages: 10
IBM ServeRAID M5014 User Manual preview
ServeRAID M5014
Brand: IBM Pages: 106
B meters IWM-LR4 Quick User Manual preview
IWM-LR4
Brand: B meters Pages: 2
Bang & Olufsen BeoSystem 4 How To Use Manual preview
BeoSystem 4
Brand: Bang & Olufsen Pages: 36
Mad Catz DVD 2 Owner'S Manual preview
DVD 2
Brand: Mad Catz Pages: 4
Danfoss VLT HVAC Operating Instructions Manual preview
VLT HVAC
Brand: Danfoss Pages: 85
Danfoss VLT Decentral FCD 300 Operating Instructions Manual preview
VLT Decentral FCD 300
Brand: Danfoss Pages: 112
Danfoss AME 55QM Datasheet preview
AME 55QM
Brand: Danfoss Pages: 4
Danfoss VLT 6000 series Manual preview
VLT 6000 series
Brand: Danfoss Pages: 27
Danfoss AME 20 Operating Manual preview
AME 20
Brand: Danfoss Pages: 16
Danfoss AK-PC 420 User Manual preview
AK-PC 420
Brand: Danfoss Pages: 20
Danfoss ADAP-KOOL AK-PC 781 User Manual preview
ADAP-KOOL AK-PC 781
Brand: Danfoss Pages: 14
Danfoss 4033 Installation And User Instructions Manual preview
4033
Brand: Danfoss Pages: 12
Danfoss vlt soft starter mcd 500 Operating Manual preview
vlt soft starter mcd 500
Brand: Danfoss Pages: 96
Samson 2406 Mounting And Operating Instructions preview
2406
Brand: Samson Pages: 32

Brands by name

Popular brands

Load more brands