Siemens SIMATIC TDC System Manual Download Page 48

Page: 48 / 228

Rack

3.1 Rack UR6021 (6DD1682-0CH3)

SIMATIC TDC hardware

System Manual, 08/2017, A5E01114865-AL

3.1.11

Ventilation/cooling

The rack is equipped with a fan tray with 6 fans for forced convection of the modules and the

system power supply.
Since the rack is not equipped with an air filter, you should provide a filter on the cabinet if

necessary.

Note
For more information, refer to section "Control cabinet (Page 20)".

Note
FANOPH
Using the FANOPH function block, you can read out the operating hours counter of the fan

from the first CPU555 and monitor it for a limit.

Fan monitor

The fans are monitored (speed). Activation of the monitoring function is delayed in order to

enable the reliable startup of the rack after you switched on power.
On failure of one or two fans, the power supply is shut down depending on the operating

mode in order to prevent thermal destruction of the modules.
The operating mode (SHUTDOWN MODE) is selected using switch S1.1, which is integrated

in the power supply. The power supply is shut down if one fan has failed and switch position

"ON" is set, or if two fans have failed and switch position "OFF" is set.

NOTICE
Safe isolation from supply
Switch off power to the rack before you remove the screws of the battery compartment.

The battery compartment cover must be unscrewed to actuate switch S1.

NOTICE
ESD Directives
Observe the corresponding ESD directives.

The operating mode setting is indicated by the "SHUTDOWN MODE" LED on the front

panel.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Brands by name

Popular brands