Siemens SIMATIC TDC System Manual Download

Page: 219 / 228

Submodules

8.2 Program memory modules CPU550/551

SIMATIC TDC hardware
System Manual, 08/2017, A5E01114865-AL

219

8.2

Program memory modules CPU550/551

Article number

Program memory module MC500

6DD1610-0AH4

Program memory module MC510

6DD1610-0AH6

Program memory module MC521

6DD1610-0AH3

Description

The program memory modules are used to store the processor program (including the

operating system) you configured in HW Config and CFC.

Installation/ programming

The program memory module is inserted into the submodule slot provided on the CPU

module and can by loaded with the user program in two ways:

●

By means of an integrated PCMCIA ("PC Card") programming adapter on the PC

(loading in offline mode)

●

Directly from the PC to the memory module inserted in the CPU module via serial

communication connection (download in online mode)

Program size

The volume of configuration data to download to the memory module (compressed to

approx. 50 %) and the free program memory space can be viewed in the CFC by selecting:
PLC / Load / Info

Memory overview

The following table shows the differences in the application and expansion of the program

memory modules:

Application

MC521

MC500

MC510

Flash memory for storing the configuration data

2 MB

4 MB

8 MB

EEPROM for variable operating parameters

8 KB

Flash memory is non-volatile and can be electrically programmed and erased.

Dimensions

Dimensions W x H x D [mm]

54 x 85.6 x 3.3 mm

Weight

30 g

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands