Siemens SIMATIC TDC System Manual Download

Page: 178 / 228

Interface module

7.1 Interface module SB10

SIMATIC TDC hardware

178

System Manual, 08/2017, A5E01114865-AL

7.1.2

Application notes

The interface module is suitable for vertical and horizontal mounting positions.

Other information

For more information on EMC and environmental conditions, refer to section "General

technical specifications (Page 37)"!

Example

The following figure shows a typical application:

Figure 7-2

Application example of an SB10 interface module on the digital I/O module SM500

The digital signals on system side are connected directly to the SIMATIC TDC modules via

the interface module. A cable SC62 is used accordingly.

Aotewell Ltd

www.aotewell.com

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands

Siemens SIMATIC TDC, System Manual

Search results

Summary of Contents for SIMATIC TDC

Reviews:

Related manuals for SIMATIC TDC

Brands by name

Popular brands