manualshive.com logo in svg

Siemens SIMATIC TDC, System Manual

Share
Download
Siemens SIMATIC TDC System Manual Download Page 132

Communication modules 

 

6.2 CP51M1 communication module 

 

SIMATIC TDC hardware 

132

 

System Manual, 08/2017, A5E01114865-AL 

6.2.3

 

Status and fault displays 

Status displays for module operation  

Table 6- 5 

Operating state displays for CP51M1 (LED H1 and H2) 

Display 

Operation state 

H1 (green) 

H2 (red) 

Off 

Off 

CP51M1 is switched off or not parameterized 

Off 

On 

CP51M1 is ready but not yet initialized 

On 

Off 

CP51M1 is initialized 

On 

On 

Power failure on CP51M1 

 

Table 6- 6 

Operating state displays for CP51M1 (LED H7 and H8) 

Display 

Operation state 

H7 (green) 

H8 (yellow) 

Off 

Off 

Module is switched off (off-current state) 

Off 

On 

STOP operating state 
Initialization error, no valid configuration found 

Flashing 

Off 

CP51M1 startup 

On 

Off 

RUN operating state 
Startup completed, CP51M1 is in normal operation 

Flashing 

Flashing 

Module is defective 

Status displays for network operation 

Table 6- 7 

Operating state displays for CP51M1 (LED H3 to H6) 

LED 

Display 

Operation state 

H3 (green) 

On 

CP51M1 has at least one full duplex connection 

Flashing 

Module is defective 

H4 (yellow) 

On 

Data traffic in transmit and/or receive direction on Ethernet 

H5 (green) 

On 

CP51M1 is communicating via Fast Ethernet (100 Mbps) 

Flashing 

CP51M1 is in the "auto-sensing phase“ 

H6 (green) 

On 

CP51M1 is connected (link) to an Ethernet compatible device (hub, 

switch, PC) 

Aotewell Ltd 

www.aotewell.com 

Industry Automation

HongKong|UK|China

[email protected]

+86-755-8660-6182

Summary of Contents for SIMATIC TDC





































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands