Siemens SIMATIC S7-200 System Manual Download

Page: 578 / 866

Debugging and troubleshooting

10.7 Hardware troubleshooting guide

S7-200 SMART

578

System Manual, V2.3, 07/2017, A5E03822230-AF

10.7

Hardware troubleshooting guide

Table 10- 1 Troubleshooting guide for the S7-200 SMART hardware

Symptom

Possible cause

Possible solution

Outputs stop working

The device being controlled has

caused an electrical surge that dam-

aged the output

When connecting to an inductive load

(such as a motor or relay), a proper

suppression circuit should be used.

Refer to the wiring guidelines in Chap-

ter 3.

Wiring loose or incorrect

Check wiring and correct

Excessive load

Check load against contact ratings

Output point is forced

Check the CPU for forced I/O

ERROR light on the CPU turns on

(Red)

Electrical noise

Refer to the wiring guidelines in Chap-

ter 3. It is very important that the con-

trol panel is connected to a good

ground and that high voltage wiring is

not run in parallel with low voltage

wiring.
Connect the M terminal on the 24 V DC

Sensor Power Supply to ground

Component damage

Send in hardware for repair or re-

placement

None of the CPU LEDs turn on

Blown fuse

Use a line analyzer and monitor the

input power to check the magnitude

and duration of the over-voltage spikes.

Based on this information, add the

proper type surge arrestor device to

your power wiring.

Reversed 24 V power wires

Refer to the wiring guidelines in Chap-

ter 3 for information about installing the

field wiring.

Incorrect voltage

Intermittent operation associated with

high energy devices

Improper grounding

Refer to the wiring guidelines in Chap-

ter 3.

Routing of wiring within the control

cabinet

It is very important that the control

panel is connected to a good ground

and that high voltage wiring is not run

in parallel with low voltage wiring.
Connect the M terminal on the 24 V DC

Sensor Power Supply to ground.

Time delay on input filters too short

Increase the input filter delay in the

system data block.

Summary of Contents for SIMATIC S7-200



































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC S7-200

Reviews:

Related manuals for SIMATIC S7-200

Brands by name

Popular brands

Siemens SIMATIC S7-200, System Manual

Search results

Summary of Contents for SIMATIC S7-200

Reviews:

Related manuals for SIMATIC S7-200

Brands by name

Popular brands