Siemens SIMATIC S7-1200 CP 1243-8 IRC Page 37 Operating Instructions Manual Download

Page: 37 / 230

Application and functions

1.10 Expansion of SINAUT projects

CP 1243-8 IRC
Operating Instructions, 02/2018, C79000-G8976-C385-03

1.10.2

Requirements for the expansion

Furthermore, the following requirements apply to importing configuration data from

STEP 7 V5 to STEP 7 Basic / Professional.
Additional modules that are not listed here are available for new projects in STEP 7 Basic /

Professional.

Requirements: Software versions

The above-mentioned configuration tools are required in the specified versions for expansion

of SINAUT projects.

●

STEP 7 V5 project
A configuration file of the communication module from a consistent STEP 7 V5 project is

required.

Requirements: Firmware versions/module update

●

Firmware of the communication module
The following firmware versions of the communication modules used are required:
–

TIM 1531 IRC - V1.1
A TIM 1531 IRC V1.0 can be exchanged for a TIM 1531 IRC V1.1 but not the other

way round.
The mode of the "Telecontrol configuration" ("Basic settings") is set to "Configure".

The existing data is adopted.

–

CP 1243-8 IRC - V2.1
Adoption of the data from STEP 7 V5 without the option of making changes
A physical V2.1 CP can be exchanged for a V3.1 CP but not the other way round. The

CP used must have hardware product version 2. The existing data is adopted.

–

CP 1243-8 IRC - V3
Adoption of the STEP 7 V5 data from the predecessor module with option to change

some configuration data
A CP V3.0 can be replaced by a CP V3.1 but not the other way round.

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC







































































































































































































































Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands

Siemens SIMATIC S7-1200 CP 1243-8 IRC, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC S7-1200 CP 1243-8 IRC

Reviews:

Related manuals for SIMATIC S7-1200 CP 1243-8 IRC

Brands by name

Popular brands