Siemens SIMATIC RTLS System Manual Download Page 151

Page: 151 / 204

Figure 7-4

Dimension drawing SIMATIC RTLS4084T - All dimensions specified in millimeters

7.4.2

Installation & Operation

7.4.2.1

Notes on installation

Before you install the devices, read this section carefully to ensure trouble-free installation and

operation.
The devices can only be used in conjunction with the RTLS localization system. Setup,

installation and use of the tools and clients of the RTLS localization system are described in the

corresponding manuals.
For commissioning, you first need to pull a marked insulating film from the housing to enable

the power supply and thus the functioning of the device.
Remove the batteries from the device when you are returning it.
Mount the device so that it has a direct line-of-sight connection to the anchors/gateways (360°

panorama view). Any type of material can impact localization. Localization through metal is not

possible. Localization through radio reflections is possible in this case which results in an

inaccurate localization.
Check the device for damages before you use it so that it is not damaged during operation.

Protect the display from objects that could scratch or otherwise damage it. The specified

operating temperature ranges must be observed.
The device contains a lithium battery.

CAUTION

Fires and burns
Improper handling of batteries can lead result in fires and burns.

The housing of the device must not be squashed, punctured or exposed to other mechanical

influences. It may only be opened to change batteries. Make sure that you observe the polarity

of the batteries (marking on the battery insert).
Never expose the device to fire, temperatures above 50 °C or direct sunlight for an extended

period of time.
Remove the storage and transport protection to commission the battery. To do this, pull out the

plastic film that is visible on the battery compartment. It is not necessary to loosen the screws

of the battery cover for this purpose.

Operating the device

The device is operated using the buttons on the front. The functioning of the button can also be

defined by means of optional software functionality.

Transponder

7.4 SIMATIC RTLS4084T

System Manual, 04/2019, C79000-G8976-C577-01

151

Summary of Contents for SIMATIC RTLS













































































































































































































Search results

Summary of Contents for SIMATIC RTLS

Reviews:

Brands by name

Popular brands

Siemens SIMATIC RTLS, System Manual

Search results

Summary of Contents for SIMATIC RTLS

Reviews:

Brands by name

Popular brands