Siemens SIMATIC RTLS System Manual Download Page 128

Page: 128 / 204

Do not clean the enclosure with liquids or abrasive, caustic or flammable cleaning products.

7.1.3

Technical specifications

Table 7-2

Technical specifications of the transponder RTLS4030T

6GT2700-3DA03

Product name

SIMATIC RTLS4030T

PULSE radio frequencies (localization)

Wireless method

IEEE 802.15.4-2011 UWB

Transmission speed

6.8 Mbps

Operating frequency rated value

3100 MHz ... 4800 MHz
6000 MHz ... 7000 MHz

Transmit power

0.037 mW (-41.3 dBm/MHz)

Range

Max. 30 m

Accuracy of the localization

0.2 m

Antennas

Built-in UWB antenna

PHASE radio frequencies (communication and optional local‐

ization)

Wireless method

IEEE 802.15.4

Transmission speed

1 Mbps

Operating frequency rated value

2400 ... 2480 MHz

Transmit power

Max. 4 dBm (can be set)

Range

Max. 50 m

Accuracy of the localization

1 m

Antennas

2.4 GHz antenna (integrated)

Bandwidth

2 MHz; data transmission over 802.15.4 channels (adjustable)

Supply voltage, power consumption

Supply voltage

VARTA CR123A battery

Service life (at 20 ℃)

Standby: 1 year
Operation: 100% UWB localization with 1 s: 6 months

Permitted ambient conditions

Ambient temperature

-10 to +50 °C

Design, dimensions, weights and connectors

Dimensions (L x W x H)

Approx. 89 x 29 x 30 mm

Weight

Approx. 90 g (including battery)

Degree of protection

IP54

Transponder
7.1 SIMATIC RTLS4030T

128

System Manual, 04/2019, C79000-G8976-C577-01

Summary of Contents for SIMATIC RTLS













































































































































































































Search results

Summary of Contents for SIMATIC RTLS

Reviews:

Brands by name

Popular brands

Siemens SIMATIC RTLS, System Manual

Search results

Summary of Contents for SIMATIC RTLS

Reviews:

Brands by name

Popular brands