Siemens SIMATIC RI 45 PIII Series Manual Download

Page: 56 / 132

2-28

RI 45 PIII, Manual

C79000-G7076-C817-01

2.11 Monitoring Functions

2.11.1 Overview

The following individual functions are available:

Temperature monitoring and over/under temperature display

Watchdog

Relay interfaces

Monitoring module messages can be forwarded to an application.

SFC program devices as well as Windows NT and Windows 98 drivers are
available for this purpose. Using these you can display status or parameterize
limiting values.

You can find descriptions of the drivers and the SFC programs on this CD
Documentation and Drivers in the directory SafeCard.

2.11.2 Status displays

The LEDs have the following meanings:

LED

OFF

GREEN

RED

Run

Watchdog inactive

Watchdog active

Watchdog executed

Temp

System OFF

Normal internal
temperature

Internal temperature be-
yond acceptance level or
cable towards tempera-
ture sensor unplugged or
interrupted.

Funktion

LED Indicators

Motherboard

Summary of Contents for SIMATIC RI 45 PIII Series





































































































































Search results

Summary of Contents for SIMATIC RI 45 PIII Series

Reviews:

Related manuals for SIMATIC RI 45 PIII Series

Brands by name

Popular brands

Siemens SIMATIC RI 45 PIII Series, Manual

Search results

Summary of Contents for SIMATIC RI 45 PIII Series

Reviews:

Related manuals for SIMATIC RI 45 PIII Series

Brands by name

Popular brands