Siemens SIMATIC RF120C Operating Instructions Manual Download

Page: 21 / 92

Communications module RF120C with application blocks for S7-1200 and S7-1500
Operating Instructions, 07/2013, C79000-G8976-C328-01

Parameter assignment and configuration

4.1

Hardware configuration

The RF120C is integrated in the hardware configuration of STEP 7 (as of V12) using an

HSP. You will find the HSP on the DVD "RFID Systems, Software & Documentation"

(6GT2080-2AA20) or on the Internet on Support homepage

(

http://www.siemens.com/automation/service&support

After installation, you can locate the RF120C module on the following path in the device

configuration:

"SIMATIC S7-1200 > Communications modules > Ident Systems > RF120C > 6GT2002-

0LA00"

4.2

Configuration

Configuration with the TIA portal

You configure the RF120C is using the TIA Portal. To do this, drag the RF120C to the device

configuration from the hardware catalog.
You can connect and configure a maximum of three RF120C modules per station.

Figure 4-1

Adding the RF120C in the device configuration

Summary of Contents for SIMATIC RF120C





























































































Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands

Siemens SIMATIC RF120C, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC RF120C

Reviews:

Related manuals for SIMATIC RF120C

Brands by name

Popular brands