Siemens SIMATIC PCS 7 SMART Getting Started Download Page 91

Page: 91 / 210

Block

name in

the project

I/O

Meaning

Value

PV_WL_Lim

Low warning limit = 7 m

SimPV

Simulated process value

300

3. Once you have entered the parameters for all the I/Os relating to a block, click "OK" for that

block.

Your settings are applied.

4. Close the CFC.

Note
Assign parameters for the "Mode" I/O for the "Pcs7AnIn" block. You can assign this

parameter only because you have not configured any external I/O modules in this Getting

Started.

6.6.13

Assigning Parameters for blocks in the "CFC_NP111"

Introduction

You have already inserted the "CFC_NP111" CFC as a process tag type. For this chart, you

still need to adapt the default parameter values to your "color_gs" project.

Note
When using process tag types, do not adapt the names of the individual blocks.

Prerequisites

The "CFC_NP111" CFC is open in the CFC Editor - Save in "color_gs_prj_MP\color_gs_prj_Prj

\Plant1\RMT1\ NP111" folder.

Creating CFCs

6.6 Working with the CFC Editor

PCS 7 SMART Getting Started - Part 1 (V9.0 with APL)

Getting Started, 12/2017, A5E42181435-AA

Summary of Contents for SIMATIC PCS 7 SMART



















































































































































































































Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands

Siemens SIMATIC PCS 7 SMART, Getting Started

Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands