Siemens SIMATIC PCS 7 SMART Page 85 Getting Started Download | Manualshive

Page: 85 / 210

background image

Procedure

1. Drag and drop the following blocks:

– "Channel" folder: Pcs7AnIn - FB1869: Signal processing of an analog input value.
– "Dosage" folder: DoseL - FB1809: Dosing of raw material.
– "Math" folder: Mul04 - FC360: Multiplies input values and returns the result at the output.
– "Control" folder: PIDConL - FB1874 : Fill level monitoring and visualization of the level

in the process mode.

– "Channel" folder: Pcs7AnOu - FB1870: Processes an analog output value signal.
– Folder "Operate": OpDi01 - FB1866: Manipulating a digital value.

2. Arrange the blocks in the CFC as shown below:

3. Close the chart.

6.6.10

Assigning parameters for the blocks in the "CFC_FC111"

Prerequisites

● The "CFC_FC111" CFC is open in the CFC Editor -

Save in folder: "color_gs_prj_MP\color_gs_prj_Prj\Plant1\RMT1\ FC111\".

● All blocks are inserted.

Creating CFCs

6.6 Working with the CFC Editor

PCS 7 SMART Getting Started - Part 1 (V9.0 with APL)

Getting Started, 12/2017, A5E42181435-AA

85

«
...
83
84
85
86
87
...
»

Summary of Contents for SIMATIC PCS 7 SMART



















































































































































































































Reviews:

No comments

Related manuals for SIMATIC PCS 7 SMART

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: Nelsen Corporation Pages: 16

Brand: National Instruments Pages: 8

Brand: National Instruments Pages: 34

Brand: Gardena Pages: 14

Brand: Gardena Pages: 4

Brand: Laser Pages: 2

Brand: LAS Pages: 6

Brand: Lars Thrane Pages: 141

Brand: Nedap Pages: 20

EP Series Pro-Bloc

Brand: Parker Pages: 11

Brand: Parker Pages: 22

Brand: Parker Pages: 2

Brand: XtendLan Pages: 12

Brand: ZBA Pages: 27

Brand: M-system Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands