Siemens SIMATIC PCS 7 SMART Page 50 Getting Started Download

Page: 50 / 210

3. To perform and complete remote configuration, follow the instructions in the online help of

the "Configure: <Selected PC Station>" dialog box.

4. Click "OK" and acknowledge the subsequent information windows by clicking "OK".

The configuration data is transferred to the PC station.

5. When the "Transfer completed successfully" message is displayed, click "Close" on the

"Configure" dialog box. You must still download the network settings to this PC station in

order to activate the network connections.

6. Select the PC station, and select PLC > Download.

The "Download" dialog box is displayed.

7. Click "Yes".

The "Stop Target Modules" dialog box is displayed.

8. Click "OK".

The download is complete.

5.4.2.6

Downloading the hardware configuration of the AS

Introduction

This section describes how to download the hardware configuration for the AS. After you have

configured and set the hardware, this information must be available to the CPU. Therefore,

download the hardware configuration to the CPU.

Prerequisites

● The CPU is in "STOP" mode.
● The color_gs project is open in SIMATIC Manager.
● The component view is activated.

Procedure

1. Select the "color_gs_prj_MP\color_gs_prj_Prj\SIMATIC 400(1)" folder in the tree view.
2. Select PLC > Compile and Download Objects.

The "Compile and Download Objects" dialog box opens.

3. Select the check boxes in the "Compile" and "Download" columns of the "color_gs\SIMATIC

400(1)\Hardware" object.

4. Click "Start".

"Downloading program changes during operation can, in the case of malfunctions or

program errors, cause serious damage to personnel and equipment! Make sure..."

message pops up.

5. Click "OK".

The compile and download operation starts. The log file is opened in the text editor when

the function is complete.

6. Close the text editor.

Initial work for the project
5.4 Configuring the stations

PCS 7 SMART Getting Started - Part 1 (V9.0 with APL)

Getting Started, 12/2017, A5E42181435-AA

Summary of Contents for SIMATIC PCS 7 SMART



















































































































































































































Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands

Siemens SIMATIC PCS 7 SMART, Getting Started

Search results

Summary of Contents for SIMATIC PCS 7 SMART

Reviews:

Related manuals for SIMATIC PCS 7 SMART

Brands by name

Popular brands