Siemens SIMATIC NET Page 59 Configuration Manual Download

Page: 59 / 464

Configuration

3.1 System

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

The parameter has the following meaning:

Parameter

Description

Range of values / note

string

Input box for the name

max. 255 characters

Result

The name is created in the system.

3.1.10

Commands in the Interface configuration mode

This section describes commands that you can call up in the interface configuration mode.

Depending on the Interface selected, various command sets are available.
In the Global configuration mode, enter the

interface

command to change to this mode.

Commands relating to other topics that can be called in the interface configuration mode can

be found in the relevant sections.

●

If you exit the Interface configuration mode with the

exit

command, you return to the

Global configuration mode.

●

If you exit the Interface configuration mode with the

end

command, you return to the

Privileged EXEC mode.

3.1.10.1

alias

Description

With this command, you assign a name to an interface. The name only provides information

and has no effect on the configuration.

Requirement

You are in the Interface Configuration mode.
The command prompt is as follows:

cli(config-if-$$$)#

Syntax

Call up the command with the following parameters:

alias <interface-name>

The parameter has the following meaning:

Parameter

Description

Range of values / note

interface-name

Name of the interface

max. 63 characters

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands