manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Diagnostics 

 

11.1 Diagnostics 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

435

 

11.1.1.2

 

show events config 

Description 

This command shows the current configuration for forwarding the messages of the various 

event types.  

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call the command without parameters: 

show events config

 

Result  

The current configuration of the events display is displayed. 

11.1.1.3

 

show events severity 

Description 

This command shows the degree of severity of an event ("Info", "Warning" or "Critical") 

starting at which a notification (sending of an e-mail, entry in the Syslog table, entry in the 

Syslog file) is generated. 

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call the command without parameters: 

show events severity

 

Result  

The corresponding degree of severity is shown for each type of notification. 

Further notes 

You configure the assignment of the degree of severity of an event and the type of 

notification with the 

severity

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Majestic UFO Assembly And Mounting Instructions preview
UFO
Brand: Majestic Pages: 2
LAPLACE INSTRUMENTS RF300 User Manual preview
RF300
Brand: LAPLACE INSTRUMENTS Pages: 21
Panorama Antennas SW3-875 LGMQM4 Series Installation Instruction preview
SW3-875 LGMQM4 Series
Brand: Panorama Antennas Pages: 3
Poynting MIMO-3-V2 User Manual preview
MIMO-3-V2
Brand: Poynting Pages: 12
Hama 00 221085 Operating Instructions Manual preview
00 221085
Brand: Hama Pages: 40
Insignia NS-ANT20FM Quick Setup Manual preview
NS-ANT20FM
Brand: Insignia Pages: 2
Panasonic CA-GA60N Installation Instructions preview
CA-GA60N
Brand: Panasonic Pages: 2
NETGEAR ProSafe ANT224D10 Installation Manual preview
ProSafe ANT224D10
Brand: NETGEAR Pages: 2
RCA ANT1400R Quick Start Manual preview
ANT1400R
Brand: RCA Pages: 2
RCA ANT1251F User Manual preview
ANT1251F
Brand: RCA Pages: 2
RCA ANT111R User Manual preview
ANT111R
Brand: RCA Pages: 2
RCA ANT1030 Specifications preview
ANT1030
Brand: RCA Pages: 2
RCA ANT111Z User Manual preview
ANT111Z
Brand: RCA Pages: 3
CommScope CMAX-DM60-Series Installation Instruction preview
CMAX-DM60-Series
Brand: CommScope Pages: 6
Barrett 2081-02-01 Installation Instructions preview
2081-02-01
Brand: Barrett Pages: 4
Ten-Haaft Caro+ Premium Mounting Instruction preview
Caro+ Premium
Brand: Ten-Haaft Pages: 44
Ten Haft samysolar Installation Instructions Manual preview
samysolar
Brand: Ten Haft Pages: 75
Ten-Haaft samy solar plus Operating Instructions Manual preview
samy solar plus
Brand: Ten-Haaft Pages: 128

Brands by name

Popular brands

Load more brands