manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Security and authentication 

 

10.2 WLAN 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

419

 

10.2.5.2

 

vap security cipher (access point) 

Description  

With this command, you configure the encryption method for the WPA authentication. 

 

 

Note 
This command is available only in access point mode. 

 

 

Note 
iPCF or iPCF-MC mode enabled 
If you want encryption with AES in iPCF or iPCF-MC mode, only keys with a 128 bit key 

length are supported. 

 

Requirement 

You are in the Interface Configuration mode of the VAP interface. 
The command prompt is as follows:  

cli (config-if-vapX-0-Y)#

 

Syntax 

Call up the command with the following parameters: 

vap security cipher { auto | aes | tkip }

 

The parameters have the following meaning: 

 

Parameter 

Description 

auto

 

TKIP or AES is used depending on the capability of the other station.  

aes

 

AES (Advanced Encryption Standard): 


Strong symmetrical block encryption 

method based on the Rijndael algorithm that further improves the functions of 

TKIP. 

tkip

 

TKIP (Temporal Key Integrity Protocol): A symmetrical encryption method with 

the RC4 algorithm (Ron’s 
Code 4). In contrast to the weak WEP encryption, TKIP uses changing keys 

derived from a main key. 

 
 

 

Note 
The encryption methods "WEP" and "TKIP" are not available with the transmission standards 

"802.11n" and "802.11n only". 

 

Result  

The encryption method is configured. 

Further notes 

You display the settings with the 

show wlan security <vapX 0/Y>

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Crest Audio SGA05328 User Manual preview
SGA05328
Brand: Crest Audio Pages: 2
L3 Narda ADFA Handling And Safety Instructions preview
Narda ADFA
Brand: L3 Pages: 122
Winegard In-Motion MVT-35B Operation Manual preview
In-Motion MVT-35B
Brand: Winegard Pages: 8
Sirius Satellite Radio Satellite Radio Antenna Installation Manual preview
Satellite Radio Antenna
Brand: Sirius Satellite Radio Pages: 10
SWR FM1 Series Manual preview
FM1 Series
Brand: SWR Pages: 12
Clas Ohlson A5960 User Manual preview
A5960
Brand: Clas Ohlson Pages: 14
Will Burt AntennaMast AM2 Operator'S Manual preview
AntennaMast AM2
Brand: Will Burt Pages: 34
CommScope CMAX-DM20 Installation Manual preview
CMAX-DM20
Brand: CommScope Pages: 4
CommScope CMAX-OUS1-UW-I53 Installation Instruction preview
CMAX-OUS1-UW-I53
Brand: CommScope Pages: 2
SPE AM-01/6 User Manual preview
AM-01/6
Brand: SPE Pages: 14
APLIC 20180619DG006 User Manual preview
20180619DG006
Brand: APLIC Pages: 20
APLIC 303340/20191008DG006 User Manual preview
303340/20191008DG006
Brand: APLIC Pages: 24
Electrovision T143EB Quick Start Manual preview
T143EB
Brand: Electrovision Pages: 4
Trantec S4.5 Series Operating Instructions Manual preview
S4.5 Series
Brand: Trantec Pages: 7
Televes Offset 630 Series Manual preview
Offset 630 Series
Brand: Televes Pages: 2
Sirio Antenne GP 3-F Installation Manual preview
GP 3-F
Brand: Sirio Antenne Pages: 2
Radio Shack 10M User Manual preview
10M
Brand: Radio Shack Pages: 8
Yagi YP-3 Manual preview
YP-3
Brand: Yagi Pages: 8

Brands by name

Popular brands

Load more brands