Siemens SIMATIC NET Page 303 Configuration Manual Download

Page: 303 / 464

Network protocols

7.3 DHCP server

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

303

The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

ip dhcp client mode {mac|client-id<client-id>|sysname}

The parameters have the following meaning:

Parameter

Description

Range of values / note

mac

The client registers with its MAC address

client-id

The client registers with the assigned ID

client-id

Name of the assigned ID

max. 32 characters

sysname

The client registers with the assigned system

name

Result

The registration mode of the DHCP client is configured.

7.3

DHCP server

This section describes commands relevant for configuring the DHCP server.

Requirement
The connected devices are configured so that they obtain the IPv4 address from a DHCP

server.

7.3.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands