Siemens SIMATIC NET Page 245 Configuration Manual Download

Page: 245 / 464

Network structures

6.3 Spanning Tree

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

245

Syntax

Call up the command with the following parameters:

show spanning-tree interface <interface-type><interface-id>

[{cost|priority|portfast|rootcost|restricted-role|

restricted-tcn|state|stats|detail}]

The parameters have the following meaning:

Parameter

Description

Range of values / note

interface-type

Type or speed of the interface

Enter a valid interface.

interface-id

Module no. and port no. of the interface

cost

Shows the port costs used to calculate

the lowest-cost path.

priority

Shows the priority of the port.

portfast

Shows whether

spanning-tree port-

fast

is enabled.

rootcost

Shows the costs of the path to the root

bridge.

restricted-role

Shows whether

spanning-tree re-

stricted-role

is enabled.

restricted-tcn

Shows whether

spanning-tree re-

stricted-tcn

is enabled.

state

Shows the status of the interface.

stats

Shows the counters of the various

BPDU transmissions.

detail

Shows detailed information about the

spanning tree settings of the interface.

For information on identifiers of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Result

The settings of the ports for the spanning tree function are displayed.

6.3.1.6

show spanning-tree l2t-edge

Description

This command displays the status of the layer 2 tunnel ports.

Note
This command is available only in access point mode.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands