Siemens SIMATIC NET Page 225 Configuration Manual Download

Page: 225 / 464

Network structures

6.2 VLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

225

6.2.2.3

vlan

Description

With this command, you create a VLAN on the device and change to the VLAN configuration

mode.

Note
The device supports up to 2 virtual networks.

In the provider backbone bridge mode, this command is used to create user, service and

backbone VLANs.

Requirement

You are in the Global Configuration mode.
The command prompt is as follows:

cli(config)#

Syntax

Call up the command with the following parameters:

vlan <vlan-id(1-4094)>

The parameter has the following meaning:

Parameter

Description

Range of values / note

vlan-id

Number of the addressed VLAN

1 ... 4094

Do not enter any leading zeros with the number of the VLAN.

Result

The VLAN is created.
You are now in the VLAN configuration mode.
The command prompt is as follows:

cli(config-vlan-$$$)#

Further notes

You delete the VLAN with the

no vlan

command.

You can display information about the VLAN with the

show vlan

command.

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands

Siemens SIMATIC NET, Configuration Manual

Search results

Summary of Contents for SIMATIC NET

Reviews:

Related manuals for SIMATIC NET

Brands by name

Popular brands