Siemens SIMATIC NET Configuration Manual Download Page 217

Page: 217 / 464

Network structures

6.2 VLAN

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface
Configuration Manual, 10/2015, C79000-G8976-C351-05

217

6.2

VLAN

This section describes commands for configuring and managing virtual networks (VLANs).

6.2.1

The "show" commands

This section describes commands with which you display various settings.
With the command

do [command]

you can execute the "show" commands in every

configuration mode.
To do this, you replace

[command]

with the "show" command that you want to execute.

Example

do show cli-console-timeout

6.2.1.1

show dot1d mac-address-table

Description

This command shows the table with the static and dynamic unicast entries and the dynamic

multicast entries.

Requirement

You are in the Privileged EXEC mode.
The command prompt is as follows:

cli#

Syntax

Call up the command with the following parameters:

show dot1d mac-address-table [address <aa:aa:aa:aa:aa:aa>]

[interface {<interface-type> <interface-id>}]

The parameters have the following meaning:

Parameter

Description

Range of values/note

address

Keyword for a MAC address

aa:aa:aa:aa:aa:aa

MAC address

Specify a valid MAC ad-

dress.

interface

Keyword for a an interface description

interface-type

Type or speed of the interface

Enter a valid interface.

interface-id

Module no. and port no. of the interface

For information on names of addresses and interfaces, refer to the section "Interface

identifiers and addresses (Page 25)".

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Search results

Summary of Contents for SIMATIC NET

Reviews:

Siemens SIMATIC NET, Configuration Manual, Page: 217 / 464

Search results

Summary of Contents for SIMATIC NET

Reviews: