manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Network structures 

 

6.1 WLAN 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

204

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

Result  

The indoor mode is enabled or the outdoor mode is disabled. 

Further notes 

You display the setting with the 

show wlan basic <wlan 0/X>

 command.  

You enable the outdoor mode with the 

wlan outdoor

 command. 

See also 

wlan outdoor (Page 203) 

6.1.5.54

 

wlan overlap-ap aging (access point) 

Description  

With this command, you configure the aging time for the list of overlapping access points. If 

an access point is inactive for longer than the set time, it is removed from the list. 

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call up the command with the following parameters: 

wlan overlap-ap aging <min(1-7200)>

 

The parameter has the following meaning: 

 

Parameters 

Description 

Range of values / note 

min

 

Time in minutes (min) 

1...7200 

Default: 120 

Result  

The aging time is specified. 

Further notes 

You display the setting with the 

show wlan advanced <wlan 0/X>

 command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

qpcom QP-AA17S120 User Manual preview
QP-AA17S120
Brand: qpcom Pages: 3
camping first Satmex mobil 2 User Manual preview
Satmex mobil 2
Brand: camping first Pages: 40
REMO BAS-2008 LTE MiMo Indoor Quick User Manual preview
BAS-2008 LTE MiMo Indoor
Brand: REMO Pages: 2
Motec Systems GPS- G1(T) User Manual preview
GPS- G1(T)
Brand: Motec Systems Pages: 7
Zonet ZWA2112 Product Data preview
ZWA2112
Brand: Zonet Pages: 2
Electro-Metrics RVR-30M Instruction Manual preview
RVR-30M
Brand: Electro-Metrics Pages: 8
Icom AL-705 Assembly Instructions Manual preview
AL-705
Brand: Icom Pages: 10
Williams Sound ANT 029 Manual And User Manual preview
ANT 029
Brand: Williams Sound Pages: 2
Williams Sound ANT 024 Setup Instructions preview
ANT 024
Brand: Williams Sound Pages: 4
Ellies AABOLTE Quick Start Manual preview
AABOLTE
Brand: Ellies Pages: 2
RCA ANT1560E Quick Start Manual preview
ANT1560E
Brand: RCA Pages: 2
CUSHCRAFT MA160V Assembly And Installation Instructions Manual preview
MA160V
Brand: CUSHCRAFT Pages: 11
CUSHCRAFT LFA-6M7EL Instruction Manual preview
LFA-6M7EL
Brand: CUSHCRAFT Pages: 12
CUSHCRAFT Big Thunder X7 Assembly & Installation preview
Big Thunder X7
Brand: CUSHCRAFT Pages: 11
CUSHCRAFT AV80 Assembly And Installation Instructions Manual preview
AV80
Brand: CUSHCRAFT Pages: 8
CUSHCRAFT A50-6S Assembly & Installation preview
A50-6S
Brand: CUSHCRAFT Pages: 8
CUSHCRAFT LFA-2M16EL Instruction Manual preview
LFA-2M16EL
Brand: CUSHCRAFT Pages: 12
CommScope CMAX-OUS1-UW-I53 Installation Instruction preview
CMAX-OUS1-UW-I53
Brand: CommScope Pages: 2

Brands by name

Popular brands

Load more brands