manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

Network structures 

 

6.1 WLAN 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

159

 

6.1.5.4

 

wlan alternative channel (access point) 

Description  

If you have activated the DFS function, you specify the alternative channel with this 

command. If the access point on the current channel discovers a disruption, it switches to 

the alternative channel.  

 

 

Note 
This command is available only in access point mode. 

 

Requirement 

●

 

The DFS function is enabled. 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call up the command with the following parameters: 

wlan alternative channel { show-channels | <number (0=auto)> }

 

The parameters have the following meaning: 

 

Parameters 

Description 

Range of values / note 

show-channels

 

Lists all available channels. 

-- 

number

 

Number of the alternative channel 

If you want the access point to 

search for a free channel itself, use 

"0".  

Default value: 0 (AUTO) 

Result  

The alternative channel is set. 

Further notes 

You display the setting with the 

show wlan basic <wlan 0/X>

 command.  

You enable the DFS function with the 

wlan dfs

 command. 

See also 

wlan dfs (Page 186) 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Alcad NEO-082 Quick Start Manual preview
NEO-082
Brand: Alcad Pages: 7
KJM A430-V Installation Manual preview
A430-V
Brand: KJM Pages: 5
M2 Antenna Systems 222-10EZ Assembly Manual preview
222-10EZ
Brand: M2 Antenna Systems Pages: 5
THOMSON ANT1538BK Operating Instructions Manual preview
ANT1538BK
Brand: THOMSON Pages: 38
WisyCom LBNA-LNNA Quick Start Manual preview
LBNA-LNNA
Brand: WisyCom Pages: 2
NXP Semiconductors PN544 Design Manual preview
PN544
Brand: NXP Semiconductors Pages: 45
TRENDnet TEW-OA14DK Specifications preview
TEW-OA14DK
Brand: TRENDnet Pages: 2
Trango Systems AD900-9 Specification Sheet preview
AD900-9
Brand: Trango Systems Pages: 2
Q-Mac TA-90 Technical Manual preview
TA-90
Brand: Q-Mac Pages: 21
TENNADYNE 100224 Assembly Instructions Manual preview
100224
Brand: TENNADYNE Pages: 12
Dahua DHI-ISC-EAA6000-P User Manual preview
DHI-ISC-EAA6000-P
Brand: Dahua Pages: 28
Etec E004ANT Instruction Manual preview
E004ANT
Brand: Etec Pages: 8
CommScope CMAX-DMF-43-UW-i53 Installation Manual preview
CMAX-DMF-43-UW-i53
Brand: CommScope Pages: 5
Solid HERCULES User Manual preview
HERCULES
Brand: Solid Pages: 39
Naxa NAA-304 Instruction Manual preview
NAA-304
Brand: Naxa Pages: 2
Hy-Gain V-4R Instruction Manual preview
V-4R
Brand: Hy-Gain Pages: 8
Hy-Gain UB-7030SAT Instruction Manual preview
UB-7030SAT
Brand: Hy-Gain Pages: 12
Hy-Gain TH-3JRS Instruction Manual preview
TH-3JRS
Brand: Hy-Gain Pages: 11

Brands by name

Popular brands

Load more brands