manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

System time 

 

5.3 SNTP client 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

125

 

5.3.1.3

 

show sntp unicast-mode status 

Description 

This command shows the current configuration of the unicast mode of SNTP.  

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call the command without parameters: 

show sntp unicast-mode status

 

Result  

The current SNTP unicast configuration is displayed. 

5.3.2

 

Commands in the global configuration mode 

This section describes commands that you can call up in the Global configuration mode. 
In Privileged EXEC mode, enter the 

configure terminal

 command to change to this mode. 

Commands relating to other topics that can be called in the Global configuration mode can 

be found in the relevant sections. 
You exit the Global configuration mode with the 

end

 or 

exit

 command and are then in the 

Privileged EXEC mode again. 

5.3.2.1

 

sntp 

Description 

With this command, you change to the SNTP configuration mode.   

Requirement 

You are in the Global configuration mode. 
The command prompt is as follows: 

cli(config)#

 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Panorama Antennas WMM9G Series Installation Instructions preview
WMM9G Series
Brand: Panorama Antennas Pages: 2
Crestron Antenna System SRD-ANT-1-PAK Installation Manual preview
Antenna System SRD-ANT-1-PAK
Brand: Crestron Pages: 16
Zehnder Rittling AX 40 Instructions Manual preview
AX 40
Brand: Zehnder Rittling Pages: 16
Ubiquiti PS-5AC Quick Start Manual preview
PS-5AC
Brand: Ubiquiti Pages: 22
Maxview Precision MXL012/55NZ Setup & User'S Manual preview
Precision MXL012/55NZ
Brand: Maxview Pages: 12
Channel Master CM-5016 User Manual preview
CM-5016
Brand: Channel Master Pages: 28
Sokkia SK-600 User Information preview
SK-600
Brand: Sokkia Pages: 2
Shively Labs 6814 Instruction Manual preview
6814
Brand: Shively Labs Pages: 34
Shively Labs 6600 Instruction Manual preview
6600
Brand: Shively Labs Pages: 46
Ten-Haaft Oyster CYTRAC DX Premium Instructions For Use Manual preview
Oyster CYTRAC DX Premium
Brand: Ten-Haaft Pages: 11
IKUSI Flashd LTE c60 Manual preview
Flashd LTE c60
Brand: IKUSI Pages: 4
Sirio Antenne ML 145 PL Installation Manual preview
ML 145 PL
Brand: Sirio Antenne Pages: 2
Sirio Antenne P 5000 LED Installation Manual preview
P 5000 LED
Brand: Sirio Antenne Pages: 2
1byone HDTV Antenna Quick Start Manual preview
HDTV Antenna
Brand: 1byone Pages: 2
Steren ANT-100 User Manual preview
ANT-100
Brand: Steren Pages: 2
cable matters 203003 User Manual preview
203003
Brand: cable matters Pages: 8
CUSHCRAFT A3S Assembly And Installation Instructions Manual preview
A3S
Brand: CUSHCRAFT Pages: 7
CUSHCRAFT BIG THUNDER XM520 Assembly & Installation preview
BIG THUNDER XM520
Brand: CUSHCRAFT Pages: 12

Brands by name

Popular brands

Load more brands