manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

113

 

 

System time 

5 

 

 

This part contains the sections describing how the system time is obtained and the settings. 
 

5.1

 

System time setting 

This section describes commands relevant for the configuration of the system time. 

5.1.1

 

The "show" commands 

This section describes commands with which you display various settings. 
With the command 

do [command]

 you can execute the "show" commands in every 

configuration mode. 
To do this, you replace 

[command]

 with the "show" command that you want to execute. 

Example 

do show cli-console-timeout

 

5.1.1.1

 

show time 

Description 

This command shows the settings of the system clock.   

Requirement 

You are in the User EXEC mode or in the Privileged EXEC mode. 
The command prompt is as follows: 

cli>

 or 

cli#

 

Syntax 

Call the command without parameters: 

show time

 

Result  

The settings for the system clock are displayed. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

KJM A430-V Installation Manual preview
A430-V
Brand: KJM Pages: 5
M2 Antenna Systems 75-5AS Quick Start Manual preview
75-5AS
Brand: M2 Antenna Systems Pages: 3
REMO BAS-2008 LTE MiMo Indoor Quick User Manual preview
BAS-2008 LTE MiMo Indoor
Brand: REMO Pages: 2
August DTA300 User Manual preview
DTA300
Brand: August Pages: 3
ANTARION OMNIPRO+ Installation And User Manual preview
OMNIPRO+
Brand: ANTARION Pages: 16
Panasonic Ramsa WX-RP921 Operating Instructions Manual preview
Ramsa WX-RP921
Brand: Panasonic Pages: 10
Panasonic Ramsa WX-ZP460 Operating Instructions Manual preview
Ramsa WX-ZP460
Brand: Panasonic Pages: 14
Panasonic TADA2420 - ANTENNA SYSTEM Installation Manual preview
TADA2420 - ANTENNA SYSTEM
Brand: Panasonic Pages: 20
Panasonic KX-FKD1 (Japanese) Manual preview
KX-FKD1
Brand: Panasonic Pages: 28
Panasonic WX-SA250P Operating Instructions Manual preview
WX-SA250P
Brand: Panasonic Pages: 56
Panasonic WX-SA250 Operating Instructions Manual preview
WX-SA250
Brand: Panasonic Pages: 56
Philips SDW1420 Specifications preview
SDW1420
Brand: Philips Pages: 2
Philips SDW1410GN Specifications preview
SDW1410GN
Brand: Philips Pages: 2
Sony VCA-130 Installation & Connection Manual preview
VCA-130
Brand: Sony Pages: 2
Sony VCA-41 Installation/Connections preview
VCA-41
Brand: Sony Pages: 2
Sony DVP-NW50 - In-wall Dvd Player Dimensions preview
DVP-NW50 - In-wall Dvd Player
Brand: Sony Pages: 3
Sony AN-XM100 Installation Manual preview
AN-XM100
Brand: Sony Pages: 4
Sony WD-880A Operating Instructions Manual preview
WD-880A
Brand: Sony Pages: 16

Brands by name

Popular brands

Load more brands