manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual, Page: 111 / 464

Share
Download
Siemens SIMATIC NET Configuration Manual Download Page 111

 

Functions specific to SCALANCE 

 

4.5 Spectrum analyzer 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 
Configuration Manual, 10/2015, C79000-G8976-C351-05 

111

 

4.5.2.2

 

wlan spectrumanalyzer start (Access Point) 

Description  

With this command you start measurement with the spectrum analyzer. If you start a new 

measurement, the previous measurement will be overwritten. 

 

 

Note 
This command is available only in access point mode. 

 

 

Note 
When the spectrum analyzer is started, all WLAN connections are terminated on both WLAN 

interfaces. The access point then also does not send any beacons. 

 

 

Note 
Do not enable the spectrum analyzer if the device is operating productively. This can 

influence the performance of the device. 

 

 

Note 
The functionality of the spectrum analyzer does not replace a dedicated spectrum analyzer. 

 

Requirement 

●

 

The WLAN interface is enabled. 

●

 

You are in the Interface Configuration mode of the WLAN interface. 
The command prompt is as follows:  

cli (config-if-wlan-0-X)#

 

Syntax 

Call the command without parameter assignment: 

wlan spectrumanalyzer start

 

Result  

The measurement is started. The measured values are logged in a file. 

Further notes 

You stop the recording with the 

wlan spectrumanalyzer stop

 command. 

You display the settings of the spectrum analyzer with the 

show wlan spectrumanalyzer

 

command. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments