manualshive.com logo in svg

Siemens SIMATIC NET, Configuration Manual

The Siemens SIMATIC NET Installation Manual is a comprehensive guide for installing and configuring the SIMATIC NET system. This user manual is available for free download from our website, providing users with valuable instructions and insights to ensure a seamless setup process.

Share
Download
background image

Functions specific to SCALANCE 

 

4.4 iPCF-MC 

 

SCALANCE W760/W720 to IEEE 802.11n Command Line Interface 

104

 

Configuration Manual, 10/2015, C79000-G8976-C351-05 

4.4.2

 

Commands in the WLAN configuration mode 

This section describes commands that you can call up in the WLAN configuration mode. 
In the Global Configuration mode, enter the 

wlan

 command to change to this mode. 

Commands relating to other topics that can be called in the WLAN configuration mode can 

be found in the relevant sections. 

●

 

If you exit the WLAN configuration mode with the 

exit

command, you return to the Global 

configuration mode. 

●

 

If you exit the WLAN Configuration mode with the 

end

 command, you return to the 

Privileged EXEC mode. 

4.4.2.1

 

wlan ipcf-mc 

 

 

Note 
The command is only available with the following device: 

•

 

SCALANCE W722-1 RJ-45 (MLFB 6GK5722-1FC00-0AA0 and 6GK5722-1FC00-0AB0 

(US version)) 

 

Description 

With this command, you enable iPCF-MC on this SCALANCE W700 device.  

Requirement 

●

 

You are in the WLAN configuration mode. 
The command prompt is as follows:  

cli(config-wlan)#

 

●

 

The access point has at least two WLAN interfaces (dual AP). 

●

 

Access point mode: Only dual APs with KEY-PLUG W780 iFeatures (MLFB 6GK5 907-

8PA00) 

●

 

Client mode: Client with KEY-PLUG W740 iFeatures (MLFB 6GK5 907-4PA00) 

●

 

The management interface and data interface must be operated in the same frequency 

band and mode and must match in terms of their wireless coverage. iPCF-MC will not 

work if both wireless interfaces are equipped with directional antennas that cover different 

areas. 

●

 

The management interfaces of all access points to which a client can change must use 

the same channel. A client scans only this one channel to find accessible access points. 

●

 

Transmission based on IEEE801.11h (DFS) cannot be used for the management 

interface. 801.11h (DFS) is possible for the data interface. 

●

 

The client cannot be operated with "Use Allowed Channel only". 

●

 

"Force roaming on Ethernet down" is automatically mirrored on the second interface. 

●

 

The following applies to clients: All configured and active SSIDs must be assigned to 

security context 1. An SSID is active when the corresponding check box "Enabled" is 

selected on the page "Interfaces > WLAN > Client". 

●

 

In Japan, iPCF-MC cannot be enabled if the data or management interface uses a 

frequency of the 4920 MHz - 5080 MH frequency band. 

Summary of Contents for SIMATIC NET

















































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for SIMATIC NET

Datron ABB1000 Technical Manual preview
ABB1000
Brand: Datron Pages: 16
Ubiquiti airMax Sector AM-9M13-120 Quick Start Manual preview
airMax Sector AM-9M13-120
Brand: Ubiquiti Pages: 20
Ubiquiti airMAX Sector AM-2G16-90 Quick Start Manual preview
airMAX Sector AM-2G16-90
Brand: Ubiquiti Pages: 12
Ubiquiti PrismAP-5-90 Quick Start Manual preview
PrismAP-5-90
Brand: Ubiquiti Pages: 10
Airgain Connect AC-HPUE Installation Instructions Manual preview
Connect AC-HPUE
Brand: Airgain Pages: 26
Poynting OMNI-703 Use Manual preview
OMNI-703
Brand: Poynting Pages: 11
M2 Antenna Systems KT34M2 Assembly Manual preview
KT34M2
Brand: M2 Antenna Systems Pages: 14
Antop AT-601B Installation Instructions Manual preview
AT-601B
Brand: Antop Pages: 9
Alpha Antenna HOA Buster User Manual preview
HOA Buster
Brand: Alpha Antenna Pages: 2
ETS-Lindgren 3110B Manual preview
3110B
Brand: ETS-Lindgren Pages: 12
ETS-Lindgren 3104C User Manual preview
3104C
Brand: ETS-Lindgren Pages: 33
Wireless Extenders YX500-PCS Installation Manual preview
YX500-PCS
Brand: Wireless Extenders Pages: 19
SELFSAT SNIPE PRO User Manual preview
SNIPE PRO
Brand: SELFSAT Pages: 133
Ten-Haaft Vision III Oyster Quick Start Manual preview
Vision III Oyster
Brand: Ten-Haaft Pages: 5
Ten-Haaft caro vision Operating Instructions Manual preview
caro vision
Brand: Ten-Haaft Pages: 57
Ubiquiti AG-HP-2G2 Quick Start Manual preview
AG-HP-2G2
Brand: Ubiquiti Pages: 24
Benelec 02632 Installation Instructions preview
02632
Brand: Benelec Pages: 2
Benelec 0202250 Instruction And Assembly Manual preview
0202250
Brand: Benelec Pages: 3

Brands by name

Popular brands

Load more brands