Siemens SIMATIC NET SCALANCE W748-1 Page 21 Operating Instructions Manual Download

Page: 21 / 78

Description of the device

4.2 Device view

SCALANCE W788-x / W748-1
Operating Instructions, 03/2022, A5E03678333-17

4.2.2

SCALANCE W7x8-x M12

①

Antenna connectors, type R-SMA female
•

Devices with one IWLAN interface:

–

Three connectors on the top

•

Devices with two IWLAN interfaces:

–

Three connectors on the top

–

Three connectors on the bottom

②

LED display

③

Connector for power supply (with cover)

④

Ethernet connector (with cover)

⑤

Screw-down cover:

- for the Reset button and

- for the PLUG slot

⑥

PLUG slot

⑦

Reset button

⑧

Grounding connector (thread M4) on the back of the device (covered)

Summary of Contents for SIMATIC NET SCALANCE W748-1















































































Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands

Siemens SIMATIC NET SCALANCE W748-1, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC NET SCALANCE W748-1

Reviews:

Related manuals for SIMATIC NET SCALANCE W748-1

Brands by name

Popular brands