manualshive.com logo in svg

Siemens SIMATIC NET RUGGEDCOM RST2228P, Installation Manual, Page: 20 / 60

Share
Download
Siemens SIMATIC NET RUGGEDCOM RST2228P Installation Manual Download Page 20

Installing the Device

2.2 Unpacking the Device

2.2

Unpacking the Device

When unpacking the device, do the following:
1. Inspect the package for damage before opening it.
2. Visually inspect each item in the package for any physical damage.
3. Verify all items are included.

Note

If any item is missing or damaged, contact Siemens for assistance.

2.3

Mounting the Device

The RUGGEDCOM RST2228P is designed for maximum mounting and display

flexibility. It can be ordered with adapters that allow it to be installed in a 48 cm (19

in) rack or directly on a panel.

NOTICE

Heat generated by the device is channeled outwards from the enclosure. As such, it

is recommended that 2.5 cm (1 in) of space be maintained on all open sides of the

device to allow for some convectional airflow.
Forced airflow is not required. However, any increase in airflow will result in a

reduction of ambient temperature and improve the long-term reliability of all

equipment mounted in the rack space.

Note

For detailed dimensions of the device with either rack or panel hardware installed,

refer to 

"Dimension Drawings (Page 40)"

.

2.3.1

Mounting the Device to a Rack

The RUGGEDCOM RST2228P can be secured to a standard 48 cm (19 in) rack using

separately purchased rack mount adapters. The adapters can be installed at the front

or rear of the chassis.
Each adapter kit includes four adapters.

RUGGEDCOM RST2228P

Installation Manual, 07/2021, C79000-G8976-1403-13

11

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228P





























































Reviews:

No comments