Siemens SIMATIC NET RUGGEDCOM RST2228P Installation Manual Download Page 16

Page: 16 / 60

Introduction

1.5 Cabling Recommendations

equipment. Recycling and disposal must be done in accordance with local

regulations.

1.5

Cabling Recommendations

Siemens recommends using SIMATIC NET industrial Ethernet shielded cables for all

Ethernet ports.

1.5.1

Protection On Twisted-Pair Data Ports

All copper Ethernet ports on RUGGEDCOM products include transient suppression

circuitry to protect against damage from electrical transients and conform with

IEC 61850-3 and IEEE 1613 Class 1 standards. This means that during a transient

electrical event, communications errors or interruptions may occur, but recovery is

automatic.
Siemens also does not recommend using copper Ethernet ports to interface with

devices in the field across distances that could produce high levels of ground

potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions.

1.5.2

Gigabit Ethernet 1000Base-TX Cabling Recommendations

The IEEE 802.3ab Gigabit Ethernet standard defines 1000 Mbit/s Ethernet

communications over distances of up to 100 m (328 ft) using all 4 pairs in category

5 (or higher) balanced, unshielded twisted-pair cabling. For wiring guidelines,

system designers and integrators should refer to the Telecommunications Industry

Association (TIA) TIA/EIA-568-A wiring standard that characterizes minimum cabling

performance specifications required for proper Gigabit Ethernet operation. For

reliable, error-free data communication, new and pre-existing communication paths

should be verified for TIA/EIA-568-A compliance.
The following table summarizes the relevant cabling standards:

Cabling

Category

1000Base-

TX Compliant

Required Action

< 5

New wiring infrastructure required.

Yes

Verify TIA/EIA-568-A compliance.

Yes

No action required. New installations should

be designed with Category 5e or higher.

Yes

No action required.

> 6

Yes

Connector and wiring standards to be determined.

Follow these recommendations for copper data cabling in high electrical noise

environments:

RUGGEDCOM RST2228P

Installation Manual, 07/2021, C79000-G8976-1403-13

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228P





























































Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228P

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RST2228P

Brands by name

Popular brands

Siemens SIMATIC NET RUGGEDCOM RST2228P, Installation Manual

Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228P

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RST2228P

Brands by name

Popular brands