Siemens SIMATIC NET RUGGEDCOM RST2228 Installation Manual Download Page 55

Page: 55 / 58

Certification
6.2 EMC and Environmental Type Tests

Test

Description

Test Levels

Severity Levels

IEC 61000-4-29

Voltage Dips

and Interrupts

DC Power Ports

30% for 0.1 s
60% for 0.1 s

100% for 0.05 s

Signal Ports

2 kV (Fail-Safe

Relay Output)

DC Power Ports

2.9 kVdc

Dielectric Strength

AC Power Ports

2 kV

Signal Ports

5 kV (Fail-Safe

Relay Output)

DC Power Ports

5 kV

AC Power Ports

5 kV

IEC 60255-27

HV Impulse

POE Power Ports

1 kV

Siemens-specified severity levels

EMC Immunity Type Tests per IEEE 1613

Description

Test Levels

Severi-

ty Levels

Enclosure Contact

± 8 kV

ESD

Enclosure Air

± 15 kV

Radiated RFI

Enclosure Ports

35 V/m (80% modulation)

Signal Ports

± 4 kV @ 2.5 kHz

DC Power Ports

± 4 kV

AC Power Ports

± 4 kV

Fast Transient

Earth Ground Ports

± 4 kV

Signal Ports

2.5 kV common mode

DC Power Ports

2.5 kV common and 1.0

kV Differential Mode

Oscillatory

AC Power Ports

2.5 kV common and 1.0

kV Differential Mode

Signal Ports

5 kV (Failsafe Relay)

DC Power Ports

5 kV

HV Impulse

AC Power Ports

5 kV

Signal Ports

2 kV (Failsafe Relay Output)

DC Power Ports

2.9 kVdc

Dielectric Strength

AC Power Ports

2 kV

Damped Oscillat-

ing Magnetic Field

Enclosure Ports

100 A/m (peak) for 1 s

(100 kHz and 1 MHz)

Environmental Type Tests

Test

Description

Test Levels

Severity Levels

IEC 60068-2-1

Cold Temperature

Test Ad

-40 °C (-40

°F), 16 Hours

RUGGEDCOM RST2228P

Installation Manual, 12/2019, C79000-G8976-1403-05

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228



























































Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RST2228

Brands by name

Popular brands

Siemens SIMATIC NET RUGGEDCOM RST2228, Installation Manual

Search results

Summary of Contents for SIMATIC NET RUGGEDCOM RST2228

Reviews:

Related manuals for SIMATIC NET RUGGEDCOM RST2228

Brands by name

Popular brands