Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO Manual Download Page 29

Page: 29 / 193

1 Technical Description, Installation Guidelines, Operation

IE/AS

−

INTERFACE LINK PN IO

as of hardware version 1, as of firmware version V2.0

Release 08/2018

C79000

−

G8976

−

C216

−

As soon as any entry is made using the keypad, the main menu appears allowing
you to navigate through the menu structure.

Figure 1-6

Display

−

Main Menu

If you have selected an entry in the list (displayed inversely), a tooltip will appear
after a brief time with further information on the entry (does not occur in the main
menu).

1.10

Settings when Using a Firewall

Please note the following when using firewalls:

Note

When using a firewall access to the following ports must be permitted depending

on the service being used:

http Port 80/TCP (for WBM)

TFTP Port 69

SNMP Port 161/UDP

SNTP Port 123 (can be changed)

SMTP Port 25

Trap Port 162/UDP

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO


































































































































































































Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews:

Siemens SIMATIC NET IE/AS-INTERFACE LINK PN IO, Manual, Page: 29 / 193

Search results

Summary of Contents for SIMATIC NET IE/AS-INTERFACE LINK PN IO

Reviews: