Siemens SIMATIC MV540 H Operating Instructions Manual Download Page 34

Page: 34 / 238

Image processing

3.1 Code reading (1D/2D codes)

SIMATIC MV500

Operating Instructions, 06/2018, C79000-G8976-C494-01

Postnet

Pharmacode

UPC A

UPC E

3.1.2

Performance characteristics when reading codes

3.1.2.1

Complex data matrix codes with "ID-Genius" detection

The self-adaptive recognition technique of the "ID-Genius" optical reader allows reliable and

robust reading of the most difficult codes. The most reliable recognition is reached by the

optical reader when you make adequate time available for the device to adapt itself by

setting a high cycle time limit.

Range of application

●

Any alignment and position of the code in the image.

●

The code can be printed both dark on a light background and light on a dark background.

●

Reading codes even when cells overlap or are largely isolated.

●

Reading of mirror-inverted codes.

●

Tolerance of distortion due, for example, to inclined installation of the image sensor

(viewing angle down to a lower limit of approximately 40 degrees to the printed surface).

Summary of Contents for SIMATIC MV540 H















































































































































































































































Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands

Siemens SIMATIC MV540 H, Operating Instructions Manual

Search results

Summary of Contents for SIMATIC MV540 H

Reviews:

Related manuals for SIMATIC MV540 H

Brands by name

Popular brands